Is your Kenmore washer not spinning items dry? Numerous other people are facing this same problem, and I hope you’ll get a valid answer to your problem in the article below.
The leading causes why your Kenmore washing machine isn’t cycling items dry is due to the usage of extra detergents, uneven loads, clogged drain hose, damaged suspension springs or shock absorbers, bokeh drive belt, lid motor coupling, weak lid switch, and many more.
In this article, we’ll discuss the reasons for this problem and provide extensive help on quickly repairing them in easy steps.
Let’s get into it!
Why Is My Kenmore Washer Not Spinning Clothes Dried?
Regardless of whether you are using a top load or a front load type of washing machine, the spinning problem is usually the same for both, and we’ll be focusing attention on the main reasons and repair in this particular section.
Here is the list of causes why your Kenmore washer won’t spin clothes dried:
#1. Extra and cheap Type Of Detergent
Too much washing powder creates a surplus of foam in your washing machine and can result in the appliance’s wear down. It also stops the garment from rubbing against one another, which is why your clothes are dripping wet.
Also, you might be using some cheap detergents, which are a consequence of the unproductive spinning of your washer.
What do you have to do?
You must be warned about the amount and type of washing powder you use for your Kenmore washing machine.
According to the owner’s manual, you should use only pure detergents.
Note that the more washing powder you use to a certain extent, the dirtier your items will be, which may lead to spinning problems.
If there’s already too much washing powder in your washer, you can run the cleaning cycle by clicking the “Cycle” button a few times on your Kenmore washer.
#2. Is the lid switch broken Or weaken
One of the ingredients that might be affected if your washer won’t spin dry usually is the Lid switch.
A broken lid switch will prevent the machine from spinning if the door isn’t getting appropriately shut. Also, the spin cycle certainly will begin with locking the door.
How do you know if the lid switch is broken? You can quickly look at this by checking the continuity of the lid switch.
What do you have to do?
What do you have to do?To repair this, clearly remove/unmount the lid switch and then move to use a multimeter to check the continuity.
We suggest putting your multimeter to the lowest ohms of resistance for pure and clear results.
If you check that there is no continuity on the lid lock switch, it surely means it’s damaged. Then you have to change that specific part.
#3. The Load In The Washer Is uneven
If your Kenmore washer isn’t cycling clothes dry, it could be due to too many loads or the few loads you need to be more equitable.
Whenever uneven or loads condition occurs, it stops your washing machine from achieving proper spin speeds, which is why your clothes still seem wet after finishing a cycle.
What do you have to do?
Ensure the loads in the washer are evenly divided to prevent spinning problems. Keep away from putting all your large laundry inside the drum simultaneously.
If you use a front load Kenmore washer, only mound your clothes up high, but they shouldn’t go the last row of holes at the front.
#4. Other items Are Trapped Inside
Due to the size or weight of the attached items in your washing machine drum, it can affect your washer.
If clothes are getting or objects getting trapped, it could also be a cause that’s why your Kenmore washer won’t spin dry as it should.
But how do these objects get caught in your washing machine? It gets inside due to the foreign items you left in your trouser’s pockets or other clothes and materials.
What should be done?
You should follow some steps to repair these issues, which are given below.
- Empty your washing machine drum by removing all the clothes inside to get direct access to the interior. Look out the drum carefully for any foreign items that might be why it breaks down.
- You can also use a torch to assist you in finding some of these tiny items. Once you detect them, use a pair of pliers or tweezers to get them out without roughing the inner of your drum.
- If you have any clothes that are getting gotten because they have many buttons devoted to them or due to their surface, you should get them out and wash them individually afterward.
Your Kenmore washing machine should begin spinning without any issues after doing this.
#5. Applying the wrong Spin Settings
You should know how to set the correct spin settings.it is vital if you want your washer to spin dry properly.
Be sure; if you have done an incorrect spin-dry setting, your washer might not spin-dry your clothes normally, which could be why they are wet and take a long time to dry.
What should be done?
Be sure you’re choosing the correct settings your machine requires based on the type of clothes you are washing and the weight of the load.
For exquisite and lightweight clothes, you should set a spin speed setting of around 400 – 600 RPM, while medium-weight clothes should be about 800 – 1000 RPM.
Tough fabric like jeans or towels should be slightly greater, around 1200 – 1400 spin speed.
However, usually note all Kenmore washing machine models might not have this option.
#6. The Drain Hose Is blocked, And The Pump Is damaged
If your washing machine drain hose is blocked, you can face extra water retention or improper leakage.
A blocked drain hose won’t allow water passage properly, cause backflow and even cause your clothes to keep hold of excess water.
In other words, your Kenmore washer won’t cycle items dry if all these occur. A blocked drain pump also could be a reason for this issue.
If the pump filter of your washer is obstructed with lint or the pump is broken, it’ll impede the passage of dirty water and, as a result, may affect the proper spinning of the machine.
What should be done?
You have to troubleshoot the effluent system by looking after and checking the drain hose and pump.
Look out for the drain hose: ensure you’ve unclogged the washing machine first. Get off the drain hose placed at the back of your washer.
Look out for any blockages or clogs inside, clean it, and join it again.
After that, if the hose is also confused, you need to adjust it to allow normal water flow.
Check the drain pump and filter: Get purified of any lint or debris blocking the filter, then change the drain pump if it’s damaged.
#7. The Drive Belt Is weakened Or Broken
The drive belt generally controls and decides the complete spinning of your washing machine.
If it gets weakened or broken, you will face problems like preventing the Motor from rotating the drum, the washer not cycling clothes dry, and many more.
What should be done?
It’s time to change the drive belt so you can repair the problem. To change the drive belt on your Kenmore washer, you should follow the steps that are given below:
- First of all, detach your washer or disconnect the switch. Also, stop the water supply.
- Get off the access panel on the back of the washing machine.
- Now, place the belt and get it out from the pulleys.
- Then, install a new drive belt by interweaving it through the pulleys before attaching your washer back.
#8. The Motor combining And Water Inlet Valve Are broken
Commonly, your washer always starts to malfunction when a part or two becomes broken.
For example, a motor combining and a water inlet valve are two essential parts that transfer power from the Motor to the agitator and Command the water flow into the machine, respectively.
If any of these parts gets broken, it could lead to cycling issues which is why we suggest checking them if your Kenmore washer won’t spin clothes dry.
Use a multimeter to check the continuity; if no continuity is limited, you should change the parts as soon as possible.
How To Enter Indicative Mode On A Kenmore Washer?
You can troubleshoot the washing machine via indicative if you have to find out the root of the problem. Follow the steps below to activate the expressive mode on your Kenmore washer.
- Besides, the machine is in standby mode, so there should be no indicators to throw light on.
- Choose any three buttons to click on the control panel, excluding the “Power” and “Start/Stop” button.
- For occasion, you can choose to click the “Wash Temp,” “Soil Level,” and “Spin Speed” buttons.
- Now, click and keep holding these three buttons simultaneously for three seconds, then release them.
- Next, connect those three buttons again & hold for another three seconds. Then, remove the buttons.
All signals should be illuminated, and that’s how to start the indicative mode.
Frequently Asked Questions
Q1: Kenmore Series 500 Washer Not Cycling Clothes Dry?
If your Kenmore series 500 washing machine isn’t cycling as it should, you must check the clutch assembly to see if it’s broken.
Decrease the washing powder you use in the washer; check for a loose drive belt before changing. Decrease loads too heavy in the washer and only set the correct spin settings.
Q2: Kenmore 110 Series Washing Machine Won’t Cycling Clothes Dry?
Kenmore 110 series washer models also get affected by not spinning-dry issues; you need to inspect if the lid motor pairing is broken and if the drain pump hose or filter is blocked or clogged.
Other areas to check are the transmission and whether it’s malfunctioning or has seized up. Be sure that the loads in the washer are balanced and should be manageable.
Checking for a blockage drain pump, broken washer belt, and suspension springs is also vital.
Q3: Kenmore 80 Series Washer Not Cycling Clothes Dry?
Your Kenmore 80 series washer is not cycling clothes dry because the suspension springs or shock absorbers are exhausted, there are uneven loads in the washer, too much washing powder, a weakened drive belt, and incorrect cycling settings.
Q4: Kenmore Elite Washer Not Cycling Clothes Dry?
Below are some repairs to carry out if your kenmore elite washer won’t cycle clothes dry:
Use proper cycling settings to check for debris and blockage in the drain hose or filter.
Repair or change the lid switch if it’s broken, avoid the extra use of washing powder, and only use the suggested type.
Additionally, inspect if there are too many loads in the washing machine, then decrease it to the minimum.
Q5: Kenmore Front Load Washer Not Cycling Clothes Dry?
For your Kenmore front load washer to start cycling -dry generally, you must ensure enough suggested detergents in the drum.
Check for any foreign items blockages; the drain hose should be free from clogs and blockages in addition to the drain filter.
If none of the above fixes work, you must divert your observation to the control panel.
If the control panel seems broken or faulty, you should make a change.
Q6: Kenmore Top Load Washer Not cycling Clothes Dry
Kenmore top load washing machines commonly face cycling issues because their lid switch is not usually working, which has to change.
Check the drive belt and motor coupling for any damages, and also inspect the agitator and the clutch if it’s broken.
Conclusion
We hope you repair the Kenmore washer that stops spinning dry generally with the assistance of our extensive guidance guide given above.
