It is very important to have the know-how of the Maytag Centennial washer issues and to know their solutions and causes. This troubleshooting guide has brought the best solutions to the problems.
All the problems with the washer should be fixed soon and for that, there is a need for the right troubleshooting guide. No washer owner has the desire to see the machine failing in front of their eyes.
There are common washer issues such as its bad lock, spinning issue, washer not starting or drainage leakage from the bottom, and many more such as transmission issues.
Your washer problems and their future fixing issues will be covered in this article. For all common problems, the easiest solution is to have the manual of the washer with you at your home which will minimize troubleshooting problems.
Let’s have a look!
We have mentioned below the Maytag Centennial washer problems and faults and troubleshooting. The washer’s problem will be discussed after.
Frequent issues with the washer and their respective causes.
| Problem | Possible cause |
| Washer not starting | The possible cause may be the power button getting stuck, a fault in the timer or the power cord, controls being locked, or due to any power failure. |
| Sensing complications | The washer spinning problem causes wrong settings, unbalanced load, and opening lids. Noisy spinning in the washer is caused by bad bearingsViolent spin is caused by damaging the rodsWasher Spin working slowly because of the maximum load |
| Lid lock complications | The cap lock is not placed in the right position or the cap is blocked |
| Leakage of the washer | Defective or missing tub seal, uneven washer, fault in air gaps, and the breakage of the pump that helps in draining |
| Spin cycle problems | The washer spinning problem causes wrong settings, unbalanced load, and opening lids.Noisy spinning in the washer is caused by bad bearingsViolent spin is caused by damaging the rodsWasher Spin working slowly because of the maximum load |
| Agitator issues | The washer faces issues such as motor coupling, drive motor, drive belt, faulty agitator, and issue with the door lock. |
| The washer is not able to drain | The lid was not put properly, clogged hose, and broken pipes |
| Transmission issues | The grinding noise of the washer causes leakage at the centerSpinning issues cause worn-out gears and smoke during the washer runs resulting in overheating problems. |
Guide for fixing washer issues and its respective 8 solutions to 8 problems.
Below we have mentioned the frequent Maytag washer causes, issues, and their easy solutions.
The Maytag washer not working
The washer doesn’t work sometimes due to the below problems:
- Power failure
You should plug in the cord and make sure that there is nothing wrong with the cord. Have an eye on all the power cords and all the failure possibilities.
- Dwelling power buttons
Keep an eye on all the power buttons whether they are stuck or not. If it is stuck, then make sure to unstick it.
- Controlling locks
This option controls the locks. It makes it impossible for the washer to act. If this controlling lock option is active, then first deactivate it to proceed.
- Time problem
The main time problem is the biggest struggle. It is not easy to work with the washer as the time issue makes it very hard to follow all the orders. Before proceeding, check whether the timer is working or not. In case time is not working then first change it to proceed.
- Washer door stuck
Make sure to shut the door and lid before working with the washer. If there you see any fault in the lid and the door then first solve that problem to proceed. You can change the lock of the lid to make it act properly.
- Fault in the power cord
Make sure that there is power and that the power switch is ok. The washer will not work if the power cord is defective. Test the power with the device called a multi-meter and if there are still faults in it you have to change it.
- Unreliable controls of the users
The user controls are not responsive and not reliable then this is the biggest issue and it will also not let the washer work properly. First, change the main power boards so that you can solve the issues.
Sensing complications of Maytag Centennial washer
Maytag Centennial washer sensor problems are faced in many different forms and they are mentioned below:
1. Maytag washer dwells on sensing
The washer is stuck on sensing because of below reasons:
- Pushing keypads
To stay in the sensing mode, the keypads have to work with the washer. After pushing keypads, you have to un-push them so that you can have the previous sensing.
- Drain blockage
The drain blockage will be breaking on the water supply. This results in no change in the sensor of the water level. To stop the drain blockage, the washer will not leave its sensing cycle.
- Jammed load
Make sure to put no loads on the washer. The extreme load of the laundry maker is hard for the washer to work. Reducing load is easy while staying in the sensing mode.
- Valve blockage
The valve needs to filter the dirt because this dirt brings and interrupts the flowing of water easily. It will help the washer to stick to the sensing mode.
- Motor blockage
Prevent the washer from motor blockage by saving it from staying in the sensing mode. What you have to do is to replace it.
- Faults seen in sensors
No water change would be detected if there is no replacement done in water level sensors. It will cause the washer to remain on the sensor.
- Lid issue
The lid lock won’t work if the condition is not okay. The washer will remain in the sensing mode and it will cause issues. What you have to do is to replace the lid after it causes any failure.
- Actuator issues
To prevent the machine to stay in the sensing mode make sure that the actuator doesn’t come in between the washer’s cycle that spins. There is a replacement required if the actuator is defective.
2. Washing complications
Maytag Centennial washer has many washing complications due to the below reasons:
- Low water
The washer will remain on the wash cycle if there is a low water level. It will remain the same until the level improves. There is a need to increase the water pressure so that the level can be raised.
- Blocked drain
The washer will stay in the wash mode only if the pipe is blocked. If this issue remains, then make sure to unblock the drain and start pumping.
- Unclean filter
The unclean strainer saves water from leakage. It says that the washer will be staying in the wash mode. If this is the issue, make sure to change the strainer.
- Faulty time, controlling boards, and a bad lid switch
If the lid is bad, the controlling switch is defective and there is a fault in the timer, the washer will get stuck on the washing cycle. Test them with the multimeter and replace the part where you see the fault.
3. Light flashing issue
The light flashing issues occurs because of the below reasons:
- Water at its lowest
The water will remain the same until the level improves. The water will be standing right on the wash cycle with the water level being low. The main thing to do is to increase the level and pressure of the water so that it can raise the water level to its highest.
- Drain blockage
If there is a blockage in the pipes, then the Maytag washer will be staying still in the washing mode. In case this happens then pump the drain and remove the blockages.
- Time, boards that are controlling washer and lid problems
If the Time boards that are controlling the washer and lid are facing defects then the washing machine cycle will get affected. Make sure to change the faulted parts and check them with the multimeter.
- Unclean filter
The unclean strainer saves water from leakage. It says that the washer will be staying in the wash mode. If this is the issue, make sure to change the strainer.
4. Maytag Centennial washer lid lock complications
The washer’s lid lock has many complications and this occurs because of the following reasons:
- Blockage and fault on the lid
If there is a lid blockage, probably spoilage, the lid light will flash. The problems will be solved only by fixing the issues and blockages.
- Fault in the lock of the lid
Make sure to put an eye on the lock of the lid to make sure it’s in place. If the lid is not placed well, correct its position and let it flash.
5. Leakage problem of the washer from the bottom
The washer is draining from the lower side because of the following reasons:
- The washer is not grounded properly
Make sure that the washer is put on the leveled surface to avoid leakage. Make sure to put it on the proper surface to stop the leakage of the washer.
- Problems in air gaps
If the air gaps are defective, then it won’t be working properly. The job of the air gaps is to hold and save the water in the washer. To avoid the leakage, make sure to change it.
- Fault in draining pumps
Replace the pump with the matching pump if you see a fault in it. If the pump is defective, then it will drain the water for no reason.
- The Seal of the tub defects
The seal is not properly working and if it is defective then the washer will leak. It will be leaking from the bottom. All you have to do is to change the seal of the tub and make sure it works properly.
6. Spin cycle faults
The washer spin cycle problems include:
- The washer will not spin
Maytag Centennial washer will not be able to spin because of the following reasons:
- Unbearable bundles
Make sure to put the bundles that are bearable in the water to give them space to spin.
- Lid is open
Also, close the lid before the washer starts otherwise, it won’t work
- Inaccurate settings
Make sure to spin the settings so that they could match your laundry. Avoid the wrong setting to make your washer spin correctly.
- The slow spinning of the washer
Mostly Maytag Centennial washer spin correctly but at a very slow speed. This happens because of the following reasons:
- The washer is not balanced properly
Make sure to put the washer on even ground to balance the load properly.
- Heavy laundry load
Make sure to minimize the heavy laundry load if the washer is spinning slowly.
- Washer spinning crazily
Check the possibilities of the spinning of the washer that is spinning crazily. It happens when the suspension rods and the other washer parts are damaged. All you have to do is to replace the defective parts to save energy which helps the washer to run properly.
- Washer making noise
Bad bearings can make your washer noisy while spinning. Check the rust damage on the washer and change it as soon as possible if bad bearing signs are seen.
7. Maytag Centennial washer problems regarding agitator
The washer may not agitate because of the faculty component. The parts that are needed are the locks of the door, motors that work properly, the kit for repairing, a belt for the drivers, and many more.
Fix it: all you have to do is to test all the parts. Replace whatever component or part is defective and test the parts with the multimeter to avoid agitation.
8. Draining issues
The Maytag Centennial washer facing draining issues because of many problems that are listed below:
- Twisted pipe
Make sure to untwist the pipe and the draining hose if it contains a twist that is blocking it and it is affecting the drainage.
- Blockage of the drain pipes and hoses
Unblock the pipes and clean the pumps if there is any dirt that is helping to increase drainage.
- Faulty in pumps
Make sure to replace the draining pump if it has defects in it.
- Switches of the lids are not working properly
If the Switches of the lids are not working properly then change it. You can also use them with the multimeter. This will help in reducing the drainage issues.
9. Transmission problems of the washer
Maytag Centennial washer faces transmission problems every day that is due to the following issues:
- Granulating noise
The washer transmission problem may generate noise during the spinning and it happens due to the seal leakage at the center. Replace the transmission to reduce the noise.
- Spinning issue
Gadgets and other problems are faced during spinning. Bring problems in the spinning. But the problems can be solved and can be fixed if the transmission is replaced.
- Producing smoke
If there is overheating in the washer, then it will release smoke while spinning. If this problem is seen, then the only solution is to replace the transmission.
Find Maytag Centennial washer codes while running diagnostic
If you have the Maytag centennials washing machine manual and you will easily clarify yourself to solve the issues.
You cannot figure out what the problem is with the Maytag Centennial washer.
To figure out the issue is to set the washing machine on the mode that helps in removing and viewing the error codes.
Maytag Centennial washer problems
Check the running diagnostic on your washer. This makes sure you check on the error codes which solve the above-mentioned problems. Still, if the washer can’t be fixed, then you can reset it.
Conclusion
This entire guide will save you from throwing your money and wasting it by calling the technicians. Make sure to take help from a professional to solve the issue immediately if the issue is out of control.
Now the well-explained and detailed troubleshooting guide of the Maytag Centennial washer is here which will help you in fixing approximately all washer problems.
