In case your dryer won’t dry clothes but gets hot, it is likely caused by one or more of the reasons in this article.
To know the reason of the issue, basically go through each step, and probably you’ll discover the cause of the issue and can settle it.
STEP 1 – CHECK YOUR CLOTHES AREN’T TOO DAMP
The leading place to begin is to check that your washing machine is set to the proper settings. Typically, because when your washing machine isn’t rinsing/spinning sufficiently, your dress is coming out of the washing machine and after that being put into the dryer too damp. When this happens, your dryer might not be able to dry your dress appropriately. When your washing machine wraps up a cycle, check that your dress isn’t too wet—they should be bit damp, not dribbling wet.
STEP 2 – CHECK YOU’RE NOT OVER-BURDENING THE DRYER
Next you have to make sure that you’re not over-burdening your dryer. A of thumb rule is that the dryer should not be filled more than 80% of its capacity. In the event that your dryer is more than 80% full, take out some of the dress, and after that attempt to see in case the dryer works appropriately. It’s also a great thought to not attempt to dry too many bulky things, like towels, at one time, as this will cause the same issue.
STEP 3 – CHECK YOUR DRYER SETTINGS
Next you have to check your dryer settings, as when they are correct or not, this will cause your dryer to heat but not dry your clothes. The primary thing to check is in case your dryer is set to a hot sufficient setting for the estimate of your clothes. Depending on the age, make, and demonstration of your dryer, it may have a programmed dry choice you’ll utilize, which can make sure your dryer works on the proper settings. Once you alter the setting, check to see in case your dryer is currently working accurately; in case not, move on to another step.
STEP 4 – CHECK THE VENT AND BUILD-UP TRAP OF YOUR DRYER
The following step is to check your dryer vent and build up trap/filter. When either of these components gets clogged, your dryer cannot work appropriately, and your stack of clothes will not dry. The buildup trap in should be cleaned specifically after each utilize to guarantee your dryer works to its maximum capacity.
Here is how the vent and trap of your dryer can be checked;
- Find the vent at the back of your dryer, and disassemble it from the dryer. You’ll be able, at that point, to give it a great clean with a vacuum cleaner. Once cleaned, you’ll be able to reattach the vent.
- Find the buildup trap and allow it a great clean. You’ll moreover utilize a vacuum cleaner to grant it a careful clean. Once cleaned, you’ll put it back into its redress position.
- Once you’ve cleaned both the vent and the trap, you’ll turn your dryer back on and check in the event that the issue has been unraveled. In case not, move on to the following step.
STEP 5 – CHECK THE WARMING ELEMENT
Next step is to check a few of the inside components that will have ended up faulty. You need keep check and balance on the issues that you’re experiencing working with gadgets and you have got a multimeter.
The primary component to check is the element that is warming. The reason of the warming element is, as the name suggests, to warm your dryer amid a cycle. When it gets to be flawed, your dryer may not reach the proper temperature, which may result in not drying your clothes.
To check the warming component, you would like to:
- Turn the control off to your dryer.
- To access the heating component, you’ll have to evacuate the top and side panels.
- Once you’ve evacuated the boards, find the warming component (check your manual if necessary). You can take help using a multimeter to check the component for coherence.
- If the test appears, it has progression, it is working correctly, and you’ll be able to move on to another step.
- If the test shows it doesn’t have coherence, the warming component will be supplanted.
- Once replaced, turn your dryer on and check on the off chance that your dryer is working accurately. In the event that not, you’ll have to check the indoor regulators.
STEP 6 – CHECK THE THERMOSTAT REGULATORS
The ultimate step is to check the indoor regulators. Depending on your particular make and model of the dryer, you may likely have both a high-limit indoor regulator and a cycling indoor regulator. If either of these indoor regulators breaks, your dryer will halt working accurately.
To check the indoor regulators, you would like to:
- Be sure that the controller is still turned off.
- If you haven’t already, you must evacuate the top and sideboards to get to the indoor regulators.
- Find the indoor regulators (check your manual to decide their area and how numerous your dryer has).
- Check the thermostats with a multimeter to see on the off chance that they have coherence.
- If either of the indoor regulators doesn’t have coherence, it’ll have to be replaced.
- Once replaced, turn your dryer back on and check if the issue has been resolved. If not, you’ll have to call a qualified specialist to allow it a moment look-over; otherwise, you might have to buy a new dryer.
